BandUp

How to Speed Up Changeovers at a Multi-Band Show

•
How to Speed Up Changeovers at a Multi-Band Show

When several bands play the same night, the bit where one band gets off stage and the next gets on is the changeover. It only lasts a few minutes, but it's the messiest part of the night: one band packing up, another setting up, the engineer resetting channels, and the room waiting. A fast changeover closes the gap before the crowd wanders off to the bar for good.

The opener finishes their last song. Before the applause dies, three of us are on stage while four of them are still coiling cables. Our drummer is looking for somewhere to set up their snare, but theirs is still on the stand. Our guitarist puts their pedalboard down and can't find a socket, because the only power strip is plugged into the other band's amp. The room waits fifteen minutes. Nobody's being difficult, everyone is doing their best. Nobody talked beforehand, that's all.

Why do changeovers drag?

Almost every delay I've seen comes from the same few places:

  • The previous band packs up in the middle of the stage, so the next band can't start setting up.
  • Pedalboards get wired on stage, power supplies get hunted for on stage.
  • Guitars get tuned on stage.
  • The engineer works out the channel list on stage by tracing cables one at a time.
  • Nobody knows who's carrying what. Everyone helps with everything and nobody finishes a job.

None of that needs to happen on stage. All of it can be sorted at home or during soundcheck.

Soundcheck or line check: what's the difference?

A soundcheck is the long version where the band's sound gets set up from scratch. Each instrument is checked on its own, monitors get dialled in, then the band plays a song or two together. On multi-band nights there usually isn't time for that for every act.

A line check is the short version: just making sure every channel is coming through. The engineer says "bass", the bassist plays a few notes, if the channel's there, on to the next. Most of the settings come from the soundcheck or the engineer's notes. Launching into a full song during a line check slows the engineer down. What they want is a few seconds of clear signal. If something is missing in your monitor, keep that short too: one sentence like "a bit more vocal in my wedge". A long explanation just holds up the next channel. We cover the full soundcheck in how to soundcheck.

Why are soundchecks done in reverse order?

On multi-band nights, soundcheck usually runs in reverse playing order: the headliner checks first, the opener checks last. The logic is simple. The last band to soundcheck leaves its gear set up and plays first, so when doors open the stage is already ready for them.

The headliner, meanwhile, pushes its gear to the very back of the stage or off to the side after checking, leaving room for the bands in front of them. That setup makes life hardest for the middle acts. They have to wait for the band before them to clear and then make room fast for the band after. If you're in the middle slot, you need to be the most prepared band of the night.

Can bands share a drum kit and amps?

They can, and in most small venues they do. Shared gear is called backline: usually a drum kit, a bass amp and one or two guitar amps. Agreeing on a shared kit is the single decision that cuts changeover time the most.

Even with a shared kit, every drummer brings a few pieces of their own, known as "breakables":

SharedDrummer brings their own
Kick drum, toms, standsSnare
Hi-hat and cymbal standsCymbals
Drum rug, throneKick pedal

During the changeover the drummer only swaps those three. Snare on the stand, cymbals on, pedal attached: a few minutes. Tearing down a whole kit and building another takes far longer and means re-placing every mic.

Sharing amps comes with a settings problem. Every guitarist sounds different, and finding your sound on someone else's amp takes time. Writing your settings down helps: gain, tone knobs, which channel. Moving to the shared amp, you set the knobs to your numbers in a minute instead of searching from scratch.

What should you agree with the other bands in advance?

Sharing gets sorted days before the gig, not on stage. If the promoter hasn't started a group chat, one of the bands can. The list is short:

  1. Who's bringing the kit? Which amps are shared?
  2. What's the running order and how long does each band play?
  3. What are the soundcheck times and order?
  4. How many channels does each band need? Are the keys stereo, how many vocal mics?
  5. Where does gear wait before it goes on stage?

That last one gets forgotten most in small venues. With no backstage, knowing which corner your gear lives in stops everyone tripping over each other's bags mid-changeover.

If someone's lending the kit, ask the drummer how it can be used: can the throne height or cymbal positions be changed? Some drummers aren't keen on people adjusting their kit, and finding that out on stage helps nobody.

What should be ready before you go on?

A fast changeover depends on what you do before you're on stage. Here's the checklist we use:

  • Pedalboard wired and tested at home. On stage it's two cables and one power plug. Spare power supply in the bag.
  • Guitars tuned and waiting at the side of the stage. Tuning happens quietly at the side of the stage before the changeover, not during it.
  • Cables labelled at both ends. You can tell what goes where even in the dark.
  • The engineer has seen your channel list in advance. A stage plot showing who's miked, who's on a DI and who stands where is enough.

For that last point, the tech rider is the document that does it all, channel list and stage plot on one page. Our tech rider guide walks through writing one.

Who does what when you come off stage?

Giving everyone one job during load-out is far faster than everyone helping with everything. A simple split:

  • Drummer: snare, cymbals, kick pedal. Leaves the shared kit as it is.
  • Guitar and bass: instrument first, then pedalboard, amp cables last.
  • Keys: keyboard, stand, power cables.
  • Singer: their own mic and notes, plus any water bottles and setlists left on stage.

Two rules beat everything else. One: no cable gets pulled until the engineer has muted the channels. Pull a cable from a live channel and the PA gives you a loud pop. Two: valve amps go to standby before being switched off. On amps with a standby switch, that's the recommended order to look after the valves.

And the outgoing band packs its bags off stage, not on it. Coiling cables on stage takes up the space where the next band needs to set up. Carry the gear to the side and pack it there, and the changeover gets minutes shorter. Last of all, someone takes one more look at the stage: a forgotten pick, capo, tuner, the setlist taped to the floor. Those usually end up under the next band's feet.

How do you hold the room during a changeover?

However fast the changeover, there's still a gap of a few minutes. Not leaving it silent keeps the night flowing. In most venues the engineer puts music on in the background during changeovers. If they don't, just ask at soundcheck.

The outgoing band's singer can announce the next act after the last song. Saying their name and that they're on in a few minutes helps keep people from drifting off. Agree on this beforehand, because a singer walking off stage is usually focused on their own finish.

The incoming band's first song matters too. Opening with something recognisable and high-energy from the first second, rather than a long quiet intro, pulls people back from the bar. But it should also be a safe pick. The sound was set in a quick line check, so a brand-new arrangement or a tricky intro is a gamble at that moment.

Then there's time. On multi-band nights every band has a slot, and running five minutes over means cutting five minutes from the next band's set. Building your setlist to the slot and keeping a droppable song at the end stops the schedule from slipping.

In BandUp the stage plot is drawn inside the tech rider by drag and drop, the channel list fills itself in from your line-up and instruments, and the venue opens the rider from a link without creating an account. If several bands are on that night, the engineer can open each band's plot on their phone ahead of time or print it as a PDF. Personal setup notes like amp settings live in each member's own notes and show up in Stage Mode without opening a menu, so the guitarist moving onto a shared amp doesn't have to remember their settings.

Even if it isn't your first gig, most of the prep for a multi-band night is the same as for a first show. The full list is in our first gig checklist.

Tags:Live Show

No one asks what's next.

Set up your band, build your first setlist in two minutes.

Set up your stage